HP Color LaserJet Enterprise flow MFP M880 — 200-Staple Cartridge Kit (2-pack) for Booklet Maker

Go back

Control panel walkaround
  • HP Color LaserJet flow MFP M880 control panel
Copy, scan, and Digital Send
  • Copy on both sides (duplex)
  • Send a scanned document to a network folder
  • Send a scanned document to one or more email addresses
  • Send a document to email by using the address book
  • Use Save to SharePoint®
  • Send a Fax
Guides
  • User Guide
Load trays
  • Tray 1
  • Tray 2
  • Load the 3x500-sheet trays
  • Load the 3,500-sheet high-capacity tray
Maintenance and clearing jams
  • Clear jams in Tray 1, the right door, and the fuser
  • Clear jams in Tray 2
  • Clear jams in the 3x500-sheet feeder and the lower-right door
  • Clear jams in the 3,500-sheet high-capacity input tray and the lower-right door
  • Clear jams in the document feeder
  • Clear top left door jams in the stapler/stacker
  • Clear Stapler 1 jams in the stapler/stacker
  • Clear stapler/stacker connection jams (hole-punch models only)
  • Clear top left door jams in the booklet maker
  • Clear Stapler 1 jams in the booklet maker
  • Clear front left door jams in the booklet maker
  • Clear jams in the output bin
  • Clean the scanner and white backing (M880)
  • Clean the document feeder pickup rollers and separation pad (M880)
Print
  • Print a stored job
  • Use easy-access USB printing
  • Add contacts to the address book from the product control panel
  • The product does not pick up paper
  • The product picks up multiple sheets of paper
  • Select staple and hole-punch locations
  • Automatically print on both sides (Windows)
  • Manually print on both sides (Windows)
  • Print multiple pages per sheet (Windows)
  • Select the paper type (Windows)
  • Create a stored job (Windows)
  • Adjust color settings (Windows)
Product views
  • Product front view
  • Product back view
  • Interface ports and security lock
  • Control panel view
  • Stapler/Stacker (with or without hole punch)
  • Booklet Maker (with or without hole punch)
  • Supplies walkaround
Quick Sets
  • Use a Quick Set
Supplies
  • Replace a toner cartridge
  • Staple cartridge refill
  • 200-Staple Cartridge Kit (2-pack) for Booklet Maker
  • Replace an imaging drum
  • Intermediate transfer belt (ITB)
  • Keyboard Overlay

  1. Open the booklet maker front door.
  2. Locate the saddle-stapler assembly . The stapler assembly has a colored handle, and is located about halfway down in the center of the booklet maker.
  3. Grasp the handle and pull the stapler assembly straight out until it stops.
  4. Locate the staple-cartridge carrier on the left side of the stapler. Pull the handle straight out, and then rotate the carrier clockwise until it locks into place, parallel to the floor.
  5. Grasp the existing staple cartridge by the tabs at the rear of the cartridge and pull straight up to remove the cartridge. Repeat for the second cartridge.

    Note: Replace both cartridges at the same time.

  6. Recycle the empty staple cartridges, and remove the two new cartridges from the packaging.
  7. Remove and recycle the staple retainer from the new cartridges.
  8. Hold the new cartridge by the two tabs, and, with the tabs to the right side, insert the cartridge straight down into the carrier until it snaps into place. Repeat the process for the second cartridge.
  9. Pull the staple-cartridge carrier straight out to release the spring-loaded catch, and then rotate the carrier down until it locks into place.
  10. Push the saddle-stapler assembly in until it stops.
  11. Close the front door.

    Note: A Staple cartridge 2 and 3 very low message displays if one or more of the staple cartridges is not fully seated.


    A Lower stapler out of position message displays if the stapler is not correctly inserted.